Vinyl siding is plastic outer surface shield for a house, which is used for beautification and water resistance, as a substitute to usual ‘wood siding’ or other substance, like aluminum or fiber cement siding. Vinyl siding is a product which is made by engineers; it was basically made from ‘polyvinyl chloride’, or ‘PVC’, resin, giving vinyl siding its name. In the UK and New Zealand a similar substance is termed as ‘uPVC’ weatherboarding.
Almost 90 percent of its mass is PVC resin, the remaining 10 percent is being used of other ingredients which create color, opacity, gloss, impact resistance, flexibility, and durability. Vinyl siding is the most commonly fixed exterior shield for residential creation in the United States and Canada. There is controversy regarding the use of vinyl siding inside the building manufacturing, particularly in the rising green building manufacturing, because of the environmental anxieties in the processing, development, and discarding of the product. In this tutorial we will see how to install vinyl siding.
Things required:
- Vinyl siding
- Vinyl accessories (J-Mold, outside corner piece)
- Measuring tape
- Hammer
- Carpenter’s level
- Siding nails
- Pencil
- Tin snips
- Chop saw (optional)
Instructions:
Set up the trim pieces first.
- Fasten similar vinyl ‘J-Mold’ to the corner of the dormer with the ceiling line and at the head of the siding spot. At the frontage wall of the dormer, set up a preformed exterior vinyl corner portion from under the eave to the ceiling line, approaching the cut in the back for a taut fit.
Level the piece of siding.
- Employ a certified siding trick to decide the angle of cut for the siding portions by putting a siding piece anywhere on the side of the dormer.
- Confirm the bottom inside corner is in touch with the roof. Smoothen the siding piece by using a carpenter’s level and use a couple of nails to tack it lightly in place once it is level. Since this is going to be a template, it doesn’t matter if it extends over the front end.
The line is an exact duplicate of the roof angle.
- Keep another piece of siding with the slant of the roof, enfolding one end of the tacked-on piece. While holding it in place, carefully mark a line by using pencil with the edge where it crossed the first piece of siding.
Tin snips make cutting angles a snap.
- Take away both sections of siding from the dormer and employ tin slices to cut with the line. This line is an accurate demonstration of the angle of the covering and you will use this portion to depict a line on each following portion of siding before setting up.
This is your template.
- Put the pattern on crown of a short portion of siding which will act as your starter piece. Create another line with the sloping cut to relocate the instruction for the first piece.
Make a gap between the nail head and the wall to prevent buckling.
- Take a measurement and cut the width of your siding and set up the first small piece, by using the given nail strip at the top to lock it to the sidewall of the dormer.
- While nailing the vinyl siding, avoid hammering the nail flush with the wall beneath. Instead, leave the top of the nail 2/8 inch from the wall. There is a little projection on the crown of the nailing band which points out the required gap.
Finished siding is level and angled correctly.
- Repeat the cutting and fixation procedure with the subsequent pieces of siding. Each one will be slightly larger as you progress but the angle will remain constant. Cut the head of the siding from the highest portion and insert it into the ‘J-Mold’ at the top to protect.
Tips and Warnings
- If your final piece of siding cracks with the middle edge, you will put in an extra ‘Under-Eave’ molding on pinnacle of the ‘J-Mold’ to support it snugly and wrap the cut.
- Security first. The steeper the top, the more risky it is. Employ ‘OSHA’ permitted tie-off to lock you while siding the dormer.
Related Content:
I like the layout of your blog and I’m going to do the same thing for mine. Do you have any tips?
This blog is great. How did you come up witht he idea?
Can this be done easily and fast? I’m planning to fit my house with vinyl siding.